Helm Full Face 320g Neutron Bad-B Nero Rosso Opaco Xs (53-54cm)
Article information
Scratch resistant paint
Each shell, after being smoothed, is given several layers of varnish. The outer shell is then coated with a transparent, scratch-resistant varnish. This makes the helmet less prone to damage.
Long Visor with anti-scratch treatment
The visor can be damaged during use. The small scratches can reduce visibility on sunny days. The anti-scratch coating makes the visor less prone to damage. However, do not let sharp objects such as jewellery or keys come into contact with the visor. Because of the coating, the visor should only be cleaned with water and dish soap. Use of strong detergents can damage the coating.
Removable inner lining
The inner lining is attached to the inner shell by snaps or velcro. The removable inner lining can be washed with neutral soap. In this way, the lining remains in good quality and the helmet fresh. In addition to the inner lining, the cheek pads are also removable.
Nose deflector
The nose deflector prevents warm air from blowing against the visor. This avoids condensation on the visor, which can reduce visibility. Alternatively, a Pinlock visor can be fitted on the helmet.
Chin deflector
By using the chin deflector, the space under the chin is closed off. In this way the helmet will be more silent and the stability will be improved. A chin deflector is only possible in a system or full-face helmet.
Quick release visor
With a quick release visor, the visor can be removed easily and quickly. No tools are needed. To remove the visor, 2 buttons must be pressed on both sides of the baseplate on the helmet.
Removable cheek pads
In addition to the inner lining, the cheek pads can also be removed. These are attached with velcro or several press-studs. Washing the cheek pads with neutral soap will keep them fresh. Make sure that the cheek pads are dry when they are put back into the helmet.
Average weight size M +/-1400gr
The weight of the helmet depends on the type of helmet. A jet-helmet is generally lighter than a system helmet. Glass fibre is also lighter than polycarbonate. The helmet is often measured in size M without visor. The second number on the sticker at the back of the helmet indicates the weight of the visor.
Sizes XS-S-M-L-XL-XXL
The size of the helmet is determined by the number of centimeters of head circumference. The size is measured with a measuring tape above the ears along the widest part of the head. The number of centimeters determines the size. The sizes are however an indication. This is no guarantee that the helmet will fit. Check per brand how the size is calculated.Click here to determine your helmet size.
Pinlock prepared
If a visor is prepared for Pinlock, you can recognize this by special pins on the side of the visor. Between these pins an extra visor can be placed which prevents the visor from fogging up. When it is cold outside and warm inside the helmet, condensation can appear. The Pinlock visor ensures that vision is maintained. The Pinlock visor can be left on when the helmet is not in use.
Intercom ready
This helmet is designed to accommodate a Bluetooth communication system or intercoms. Allows you to install a communication system without changing the helmet itself. The preparation of the communication system or intercom does not compromise in any way the safety of the helmet. The helmet has a housing provided for headphones and a mounting is available to keep the microphone rod ready to use
ECE-R 22.06 certification
If you want to participate in traffic on a moped, scooter or motorbike in Europe you are obliged to wear a helmet with the ECE certification. This certification meet of a number of minimum requirements that a helmet must pass. The ECE certification can be found on the label attached to the chinstrap.
Air stream system
This helmet is equipped with front air vents which allows the fresh air inlet that, passing through the proper ducting in the inner shell, arrives to the rider, helping to keep fresh and oxygenated the inside of the helmet.
High visibility inner lining
The high visibility inner linings are made with inserts or bands in reflective material or in fluo yellow to make the helmet more visible, increasing passive safety.
Elastic fabric loop
Elasticated fabric loop that allows you to lock the excess strap in the folded position.
Prepared for glasses use
The internal padding is made with a special housing for the temples of the glasses, this system is designed to offer optimal comfort to those who wear glasses.
HPT shell
The shell is injection molded, the thermoplastic polymers, once cooled and hardened after the molding process, guarantee a high mechanical resistance for maximum impact protection, in a wide range of temperatures, and a high capacity to dissipate energy resulting from an impact. Furthermore, the molded shell maintains its original structure, without deformation or instability, for many years.Specifications
| Size | : | XS / 53-54cm |
| Type | : | Full face |
| Color | : | Black |
| Pinlock | : | Yes |
Fits
Helm Full Face 320g Neutron Bad-B Nero Rosso Opaco Xs (53-54cm) fits the following vehicles:Documentation
User manual (Multiple languages):
Instruction_Manual_320.pd...
Instruction_Manual_320.pd...
Additional products
Recommended products
Spare parts
