Helm Full Face 363s Shot Nippo Bianco Oro Xs (53-54cm)
Article information
Long Visor with anti-scratch treatment
The visor can be damaged during use. The small scratches can reduce visibility on sunny days. The anti-scratch coating makes the visor less prone to damage. However, do not let sharp objects such as jewellery or keys come into contact with the visor. Because of the coating, the visor should only be cleaned with water and dish soap. Use of strong detergents can damage the coating.
Integrated sun visor
The integrated sun visor is easy to use. By pulling the lever of the visor, the visor comes down. This way, you don't have to wear sunglasses on sunny days. The sun visor blocks most of the sun's rays and can be combined with sunglasses. When it gets too dark, you can easily pull the visor up again and use the transparent visor.
Removable inner lining
The inner lining is attached to the inner shell by snaps or velcro. The removable inner lining can be washed with neutral soap. In this way, the lining remains in good quality and the helmet fresh. In addition to the inner lining, the cheek pads are also removable.
Perforated inner lining
The ventilation system in the helmet ensures a constant air flow. Through the perforated inner lining, this air, which enters through the air channels, can also reach the skin. This way it always stays cool inside the helmet. In winter, the ventilation system can be closed so no air enters the helmet.
Nose deflector
The nose deflector prevents warm air from blowing against the visor. This avoids condensation on the visor, which can reduce visibility. Alternatively, a Pinlock visor can be fitted on the helmet.
Chin deflector
By using the chin deflector, the space under the chin is closed off. In this way the helmet will be more silent and the stability will be improved. A chin deflector is only possible in a system or full-face helmet.
Micrometric buckle
The micrometric buckle is the most frequently used buckle on helmets and easy to use. The rattle buckle ensures that it can be adjusted to the correct position. The buckle is easily opened by pulling the red loop.
Helmet graphics with scratch resistant varnish
Each helmet is carefully treated to achieve the right finish. After the helmet has been smoothed, it is sprayed in several layers of colour. Then the helmet is covered with water-based graphics. Finally, the helmet is covered with a transparent scratch-resistant lacquer.
Quick release visor
With a quick release visor, the visor can be removed easily and quickly. No tools are needed. To remove the visor, 2 buttons must be pressed on both sides of the baseplate on the helmet.
Average weight size M +/-1550gr
The weight of the helmet depends on the type of helmet. A jet-helmet is generally lighter than a system helmet. Glass fibre is also lighter than polycarbonate. The helmet is often measured in size M without visor. The second number on the sticker at the back of the helmet indicates the weight of the visor.
Sizes XS-S-M-L-XL-XXL
The size of the helmet is determined by the number of centimeters of head circumference. The size is measured with a measuring tape above the ears along the widest part of the head. The number of centimeters determines the size. The sizes are however an indication. This is no guarantee that the helmet will fit. Check per brand how the size is calculated.Click here to determine your helmet size.
Different shell sizes
By using different helmet shells the helmets get an even better fit. The smaller helmet shells are used for the smaller sizes and the larger helmet shells for the larger sizes. In this way, size XS has a smaller helmet shell than size XXL.
Titling visor fastening system
The tilting fastening system presses the visor even more firmly against the rubber rim of the helmet. In this way, the visor closes optimally. This will not only prevent the cold but also makes the helmet more silent. It is important to lubricate the rubber edge with a little silicone to prevent it from dehydrating.
ECE-R 22.06 certification
If you want to participate in traffic on a moped, scooter or motorbike in Europe you are obliged to wear a helmet with the ECE certification. This certification meet of a number of minimum requirements that a helmet must pass. The ECE certification can be found on the label attached to the chinstrap.
Extracool Inner Lining
The extracool inner linings are made with a new breathable fabric with an innovative design.
Air stream system
This helmet is equipped with front air vents which allows the fresh air inlet that, passing through the proper ducting in the inner shell, arrives to the rider, helping to keep fresh and oxygenated the inside of the helmet.
High visibility inner lining
The high visibility inner linings are made with inserts or bands in reflective material or in fluo yellow to make the helmet more visible, increasing passive safety.
Elastic fabric loop
Elasticated fabric loop that allows you to lock the excess strap in the folded position.
Prepared for glasses use
The internal padding is made with a special housing for the temples of the glasses, this system is designed to offer optimal comfort to those who wear glasses.
HPT shell
The shell is injection molded, the thermoplastic polymers, once cooled and hardened after the molding process, guarantee a high mechanical resistance for maximum impact protection, in a wide range of temperatures, and a high capacity to dissipate energy resulting from an impact. Furthermore, the molded shell maintains its original structure, without deformation or instability, for many years.
Visor lock in closed position
The visor is equipped with a special locking mechanism that allows it to be locked firmly in place when closed.
Emergency release system
SOS RELEASE SYSTEM allows you to quickly remove the cheek pads, in case of emergency, while the helmet is worn. By pulling the red emergency strips, the snap buttons are released and it will be possible to extract the cheek pads from the lower part of the helmet. This system should only be used in an emergency.Specifications
| Size | : | XS / 53-54cm |
| Type | : | Full face |
| Color | : | White |
| Pinlock | : | Yes |
Fits
Helm Full Face 363s Shot Nippo Bianco Oro Xs (53-54cm) fits the following vehicles:Documentation
User manual (Multiple languages):
Instruction_Manual_363.pd...
Instruction_Manual_363.pd...
Additional products
Recommended products
Spare parts
