Helmet full face CGM 321A ATOM MONO matt black (double visor)
Article information
CGM 321A ATOM MONO
Excellent aerodynamic, shell in HPT (High Performance Terpolymer), Air Stream System and hidden sun visor, the 321 ATOM owns all the requirements to be the answer to any driving condition. The linings, realized with hexagonal thermoformed top for a better driving comfort, are equipped with external high visibility bands to increase the passive safety, and with nose deflector and neck deflector to increase the quietness. The external visor is tilting, for a complete adherence on the perimetral seals. The helmet is prepared for the installation of the Pinlock 70 lens, to place an aftermarket communication system and to be used even by who wears glasses. The equipment is completed by micrometric buckle and elastic strap loop.
Long Visor with anti-scratch treatment
The visor can be damaged during use. The small scratches can reduce visibility on sunny days. The anti-scratch coating makes the visor less prone to damage. However, do not let sharp objects such as jewellery or keys come into contact with the visor. Because of the coating, the visor should only be cleaned with water and dish soap. Use of strong detergents can damage the coating.
Integrated sun visor
The integrated sun visor is easy to use. By pulling the lever of the visor, the visor comes down. This way, you don't have to wear sunglasses on sunny days. The sun visor blocks most of the sun's rays and can be combined with sunglasses. When it gets too dark, you can easily pull the visor up again and use the transparent visor.
Luxury inner lining
The inner lining is more luxurious compared to the standard lining. The lining is made of refined materials and has a luxurious look. The colours of the lining match the exterior of the helmet. The luxury lining can often be found on the more expensive helmets.
Removable inner lining
The inner lining is attached to the inner shell by snaps or velcro. The removable inner lining can be washed with neutral soap. In this way, the lining remains in good quality and the helmet fresh. In addition to the inner lining, the cheek pads are also removable.
Nose deflector
The nose deflector prevents warm air from blowing against the visor. This avoids condensation on the visor, which can reduce visibility. Alternatively, a Pinlock visor can be fitted on the helmet.
Chin deflector
By using the chin deflector, the space under the chin is closed off. In this way the helmet will be more silent and the stability will be improved. A chin deflector is only possible in a system or full-face helmet.
Micrometric buckle
The micrometric buckle is the most frequently used buckle on helmets and easy to use. The rattle buckle ensures that it can be adjusted to the correct position. The buckle is easily opened by pulling the red loop.
Helmet graphics with scratch resistant varnish
Each helmet is carefully treated to achieve the right finish. After the helmet has been smoothed, it is sprayed in several layers of colour. Then the helmet is covered with water-based graphics. Finally, the helmet is covered with a transparent scratch-resistant lacquer.
Quick release visor
With a quick release visor, the visor can be removed easily and quickly. No tools are needed. To remove the visor, 2 buttons must be pressed on both sides of the baseplate on the helmet.
Removable cheek pads
In addition to the inner lining, the cheek pads can also be removed. These are attached with velcro or several press-studs. Washing the cheek pads with neutral soap will keep them fresh. Make sure that the cheek pads are dry when they are put back into the helmet.
Average weight size M +/-1450gr
The weight of the helmet depends on the type of helmet. A jet-helmet is generally lighter than a system helmet. Glass fibre is also lighter than polycarbonate. The helmet is often measured in size M without visor. The second number on the sticker at the back of the helmet indicates the weight of the visor.
Pinlock prepared
If a visor is prepared for Pinlock, you can recognize this by special pins on the side of the visor. Between these pins an extra visor can be placed which prevents the visor from fogging up. When it is cold outside and warm inside the helmet, condensation can appear. The Pinlock visor ensures that vision is maintained. The Pinlock visor can be left on when the helmet is not in use.
Titling visor fastening system
The tilting fastening system presses the visor even more firmly against the rubber rim of the helmet. In this way, the visor closes optimally. This will not only prevent the cold but also makes the helmet more silent. It is important to lubricate the rubber edge with a little silicone to prevent it from dehydrating.
Intercom ready
This helmet is designed to accommodate a Bluetooth communication system or intercoms. Allows you to install a communication system without changing the helmet itself. The preparation of the communication system or intercom does not compromise in any way the safety of the helmet. The helmet has a housing provided for headphones and a mounting is available to keep the microphone rod ready to use
ECE-R 22.06 certification
If you want to participate in traffic on a moped, scooter or motorbike in Europe you are obliged to wear a helmet with the ECE certification. This certification meet of a number of minimum requirements that a helmet must pass. The ECE certification can be found on the label attached to the chinstrap.
Air stream system
This helmet is equipped with front air vents which allows the fresh air inlet that, passing through the proper ducting in the inner shell, arrives to the rider, helping to keep fresh and oxygenated the inside of the helmet.
High visibility inner lining
The high visibility inner linings are made with inserts or bands in reflective material or in fluo yellow to make the helmet more visible, increasing passive safety.
Prepared for glasses use
The internal padding is made with a special housing for the temples of the glasses, this system is designed to offer optimal comfort to those who wear glasses.
HPT shell
The shell is injection molded, the thermoplastic polymers, once cooled and hardened after the molding process, guarantee a high mechanical resistance for maximum impact protection, in a wide range of temperatures, and a high capacity to dissipate energy resulting from an impact. Furthermore, the molded shell maintains its original structure, without deformation or instability, for many years.Specifications
| Size | : | XS / 53-54cm |
| Type | : | Full face |
| Color | : | Black |
| Pinlock | : | Yes |
Fits
Helmet full face CGM 321A ATOM MONO matt black (double visor) fits the following vehicles:Additional products
Recommended products
Spare parts
