Modular helmet CGM Berlino Italia white (double visor)
Article information
CGM 508I BERLINO ITALIA
The 508 modular helmet is a modern design helmet with double P/J approval. It has an external visor, with an extensive field of vision, but a PINLOCK anti-fog screen can also be mounted. It also has a metal chin guard closure, a button to lock the chin guard in the raised position and an invisible smoke inner edge.
Information: A modular helmet can be approved P (which means "Protective": helmet with protective chin protection) or P/J (helmet with protective chin protection usable in closed or open position).
The double P/J homologation therefore makes it possible to travel with the modular helmet in closed or open configuration, but it is necessary to lock the chin guard in the open position with the correct button. For optimum protection, however, it is essential to always drive with the chin strap closed.
Scratch resistant paint
Each shell, after being smoothed, is given several layers of varnish. The outer shell is then coated with a transparent, scratch-resistant varnish. This makes the helmet less prone to damage.
Polycarbonate shell
A polycarbonate outer shell is relatively cheap to produce, which makes the helmets affordable. The helmet is produced by using a mould where the material is poured and compressed. By using plasticizers, the plastic becomes elastic. Through exposure to UV-light and various weather conditions, these plasticisers deteriorate. This means that a polycarbonate helmet should be replaced after approximately 5 years.
Front and/or rear ventilation system
The ventilation system consists of air inlets at the front and/or rear. Through air channels in the inner shell, the incoming air is guided through the helmet. In this way, the rider experiences a constant air flow which also guarantees a pleasant temperature inside the helmet.
Large surface Visor
In order to have an even better view of the road, the visor is equipped with a larger surface. This gives the driver a better view of the traffic from the side. This enhances comfort and safety while riding.
Integrated sun visor
The integrated sun visor is easy to use. By pulling the lever of the visor, the visor comes down. This way, you don't have to wear sunglasses on sunny days. The sun visor blocks most of the sun's rays and can be combined with sunglasses. When it gets too dark, you can easily pull the visor up again and use the transparent visor.
Removable inner lining
The inner lining is attached to the inner shell by snaps or velcro. The removable inner lining can be washed with neutral soap. In this way, the lining remains in good quality and the helmet fresh. In addition to the inner lining, the cheek pads are also removable.
Perforated inner lining
The ventilation system in the helmet ensures a constant air flow. Through the perforated inner lining, this air, which enters through the air channels, can also reach the skin. This way it always stays cool inside the helmet. In winter, the ventilation system can be closed so no air enters the helmet.
Nose deflector
The nose deflector prevents warm air from blowing against the visor. This avoids condensation on the visor, which can reduce visibility. Alternatively, a Pinlock visor can be fitted on the helmet.
Chin deflector
By using the chin deflector, the space under the chin is closed off. In this way the helmet will be more silent and the stability will be improved. A chin deflector is only possible in a system or full-face helmet.
Micrometric buckle
The micrometric buckle is the most frequently used buckle on helmets and easy to use. The rattle buckle ensures that it can be adjusted to the correct position. The buckle is easily opened by pulling the red loop.
Pinlock prepared
If a visor is prepared for Pinlock, you can recognize this by special pins on the side of the visor. Between these pins an extra visor can be placed which prevents the visor from fogging up. When it is cold outside and warm inside the helmet, condensation can appear. The Pinlock visor ensures that vision is maintained. The Pinlock visor can be left on when the helmet is not in use.
ECE 22-05 certification
If you want to participate in traffic on a moped, scooter or motorbike in Europe you are obliged to wear a helmet with the ECE certification. This certification meet of a number of minimum requirements that a helmet must pass. The ECE certification can be found on the label attached to the chinstrap.Specifications
| Size | : | S / 56cm |
| Type | : | System |
| Color | : | White |
Fits
Modular helmet CGM Berlino Italia white (double visor) fits the following vehicles:Documentation
Specifications (Italian):
PINLOCK_description_it.pd...
PINLOCK_description_it.pd...
Specifications (English):
PINLOCK_description_en.pd...
PINLOCK_description_en.pd...
Specifications (French):
PINLOCK_description_fr.pd...
PINLOCK_description_fr.pd...
Specifications (Dutch):
PINLOCK_description_nl.pd...
PINLOCK_description_nl.pd...
Specifications (German):
PINLOCK_description_de.pd...
PINLOCK_description_de.pd...
Additional products
Recommended products
Spare parts
